Lesson 8

Check my plan and assembly steps

Check my plan is Dry Fit's look over a project before you cut: it lists what's missing or risky, the most serious first, and says why. Let Dry Fit look the desk over before you cut, then step through the order it goes together.

You need: The desk from Lesson 6, or its project file.

What you'll build

The built-in desk in 3D with name tags: Desktop, Side times 4, Shelf times 6, Wall side times 2 and Wall shelf times 3
The desk from Lesson 6, now with the Desktop joined to the sides. Nothing changes size in this lesson.

Overall size 60" W × 23-1/4" D × 78" H

Parts key

NameSizeWhat it isFrom
Desktop60" × 23-1/4"The desk's top, joined to the four sides with Dominos in this lessonSheet A
Side29-1/4" × 23-1/4" ×4Cabinet sides, two per cabinetSheet A
Shelf17" × 23" ×6Cabinet shelves, three per cabinetSheet B
Back29-1/4" × 17-1/4" ×2Cabinet backs, 1/4" plywoodSheet D
Wall side30" × 11" ×2The wall unit's endsSheet B
Wall shelf59" × 10-3/4" ×3The wall unit's shelvesSheet C
Wall back59-1/4" × 30"The wall unit's back, 1/4" plywoodSheet D

After this lesson you can let Dry Fit check a plan before you cut and step through the glue-ups in order.

Before you cut, let Dry Fit look the desk over, then see the order it goes together. This lesson uses the finished desk from Lesson 6. If it isn't open, open built-in-desk.dryfit.json with Open project file… in the project menu.

  1. Click Check at the top. Its red badge reads 1: one thing to fix before you cut. Check my plan lists what's missing or risky, the most serious first, and says why. On the desk there are three: Desktop isn't joined to anything, Wall shelf will sag under books (each Wall shelf spans 58-1/2" between the Wall side parts), and a tip, 3/4" plywood is rarely 3/4".
Check my plan on the desk: under Fix before you cut, Desktop isn't joined to anything with a Join with Dominos button; under Worth a look, Wall shelf will sag under books with a button to add a hard maple nosing; and a tip about 3/4 inch plywood
Each finding has its fix as a button. Show in the shop selects the parts it's about.
  1. Under Desktop isn't joined to anything, click Join with Dominos. Dry Fit cuts Domino mortises where the Desktop sits on the four Side parts, the finding goes, and so does the badge on Check. Undo takes a fix back. Which joint? explains when that joint is the right one.
  2. Click Shop, then Assembly steps on the view toolbar. A card at the foot of the 3D view shows Step 1 of 4, Glue up Case: the parts by name and cut list number, the order to put them in, the joints, the glue and the clamps. Now that the Desktop is joined, both cabinets and the desktop glue up as one case. (Without the fix it would be 7 steps, each cabinet on its own.)
The Assembly steps card on the desk, step 1 of 4, Glue up Case: Desktop, four sides and six shelves, the order to put them together, the joints, and 14 clamps, 6 of 72 inches and 8 of 36 inches, with a note about glue open time
Step 1 glues up the four Side parts, six Shelf parts and the Desktop. With 16 joints it warns that ordinary yellow glue skins before you'd finish, and suggests a dry fit, a helper and a glue with more open time.
  1. Click Next (or press →) to step through: step 2 puts both Back parts on, step 3 glues up the wall unit (Glue up Wall), and step 4 puts the Wall back on. The step's parts are outlined and slide into place in 3D. Back or ← goes back, and Esc closes the card.
Step 3 of 4, Glue up Wall: the wall unit outlined above the desk, with its parts, order, joints and 6 clamps of 72 inches
Step 3: the two Wall side and three Wall shelf parts. The line at the foot of the card gives the fewest clamps for the whole job.

What you get: a desk with nothing left loose, and the order it goes together with the clamps each glue-up takes. The same steps print in the shop plan PDF, under Assembly steps.