Join parts that touch with Dominos, dowels, biscuits or pocket screws, on a small bench.
Time15 min
BuildsA 48" bench seat
You need: Dry Fit open in your browser, or the iPad or Mac app. No account.
Lesson 7 as a video, 3 minutes, with captions on screen and no sound. The steps below are the same.
What you'll build
The bench at the end of this lesson, with the names you'll see in Dry Fit.
Overall size48" W × 15" D × 18" H
Parts key
Name
Size
What it is
From
Top
48" × 15"
The seat, joined to both sides with 8 Dominos
Sheet A
Side
17-1/4" × 15" ×2
The two legs, standing on end
Sheet A
After this lesson you can join parts that touch with Dominos, dowels, biscuits or pocket screws, and read the joints in the cut list.
Loose tenons, dowels, biscuits and pocket screws join parts that touch, the way they'll be glued. Nothing has to overlap. This short build is a 48" bench seat on two sides, joined with Domino tenons. Start a new project with New project in the project menu (click the project's name at the top). Then click Untitled project at the top, click the Name box in the menu that opens, and type Domino bench.
The lumber rack starts on 3/4" Birch Plywood, 4' × 8': click Add sheet to shop. It comes in as Sheet A, selected. Sheets are rarely square from the yard, so the panel on the right suggests squaring it first. Click Square it, keep 1/4", and click Square sheet. Dry Fit trims one long edge straight, then one end square to it, the way you would at the saw. Sheet A is now 95-3/4" × 47-3/4" and still selected.
Before you click Square sheet: the red lines are the trimmings, and the form says what's left, 95-3/4" × 47-3/4". The cut sequence starts with these squaring cuts.
Cut the parts from the squared sheet. Each row starts from the piece named in the first column, as the In the shop list shows it; click that row first if it isn't selected. Type the name in the form's Name the strips or Name the pieces box.
Select
Tool
Size
How many
Name
Sheet A, 95-3/4" × 47-3/4" (still selected)
Rip
15"
1
Strip
Strip, 95-3/4" × 15" (selected after the rip)
Crosscut
48"
1
Top
Offcut A1, 47-5/8" × 15"
Crosscut
17-1/4"
2
Side
Strip is the 15" strip the top and both sides come from. Cutting the Top from it uses it up and leaves Offcut A1, 47-5/8" × 15", which the two sides come from. The rest of the sheet keeps the name Sheet A, now 95-3/4" × 32-5/8". When you're done, In the shop says 3 parts: Top 48" × 15" and two Side 17-1/4" × 15". Offcut A1 is down to 12-7/8" × 15".
After the three cuts: the parts and the leftovers, by the names In the shop gives them.
Place the parts so they touch where they'll be glued. Stand each Side on end and drag them into place against the back wall, one at Left edge 2" and the other at 45-1/4". The two are the same, so either can go on either end. Then drag the Top into the corner over them and hold Shift to lift it until it sits on the sides: the tag says Touching Side, Off floor reads 17-1/4", and the chip says the top can take loose joinery or pocket screws there. The numbers are below if you'd rather type them: click the part in In the shop, click its orientation under Position, then type the three boxes.
Part
Orientation
Left edge
Off floor
Back edge
Top
Lay flat
0
17-1/4"
0
Side
On end
2"
0
0
Side
On end
45-1/4"
0
0
Click Top (48" × 15") in In the shop and click Loose joinery. A Side works too. Every place a part meets the one you selected is listed with a checkbox. Here it lists two: Side's top end meets this part (left) and (right).
Leave Loose tenon and Domino DF 500 picked. Each joint in the list shows its own count and depths: 4 Dominos (6 × 40), 25 mm deep in the side and 15 mm in the top. The top is only 3/4" thick, so the deeper half goes into the sides' end grain. The line under the list gives the total, 8 Dominos. Size, count and depth are under Change size, count or depth if you want different ones. Inside it, Auto picks the size for the stock, and the suggested size stays underlined when you pick another.
Before you click Cut mortises: red marks where the mortises will go, in the Top and in both Side parts. The Check badge reads 3 until they're joined.
Click Cut mortises. The badge on Check goes away. Then open Cut list. Assembly lists which parts join and how, and Hardware adds up the Dominos to buy. Both go in the PDF too.
Assembly: Side ×2 joins Top with four Dominos each, at the top end. Hardware: eight Domino tenons.
When two joints run into each other
Where two aprons meet at a table leg, their Dominos can meet inside the leg. Dry Fit puts a red × where two holes run into each other, and the list under each joint says where each of those holes sits and what it runs into. Click the × to choose which one to remove: the menu names the part each hole joins, and says so when it's the last one holding that part on. The matching hole in the other part goes too, and Assembly, Hardware and the cut sequence update. Show each tenon under any joint lists them all if you want to remove one that doesn't collide.
A separate example table corner: Front apron and Side apron meet at a Leg. Two collisions in the leg, one × each. The open menu offers the Domino joining each apron.
Dowels, biscuits and pocket screws
Pick Dowels or Biscuits at the top of the same form. For pocket screws, click Pocket screws: the pockets go in the part whose end or edge meets the other, on the face you pick, and Kreg's chart sets the jig and screw length from that part's thickness. Thread is picked by the part the screws go into: fine for hardwood, coarse for softwood and plywood.