Lesson 16

Your shop

Tell Dry Fit which tools you have and how big your machines are, and the joinery, tips and Check my plan follow them. Then pack a base cabinet onto fewer sheets and cut it setup by setup.

You need: Dry Fit open in your browser. For step 5, the desk's offcuts kept in My shop's stock (Lesson 10). A free account only for the PDF at the end.

What you'll build

The base cabinet from the library, a drawer over a door on a toe-kick, with name tags on Base side, Base top, Base drawer front and Base door
The library's base cabinet, planned for a track saw, a pocket-hole jig and an 18" table saw, on one sheet fewer.

Overall size 24" W × 24" D × 34-1/2" H

Parts key

NameSizeWhat it isFrom
Base side30-1/2" × 23-1/4" ×2The cabinet sidesSheet C
Base bottom, Base top23" × 23"The box's bottom and topSheet C
Base shelf22-7/16" × 23"The shelf on pinsSheet C
Base door24-1/4" × 23-7/8"The full-overlay doorSheet C
Base drawer front23-7/8" × 6"The drawer's faceSheet C
Base drawer box side, back, front, bottom22" × 4-1/2", 21" × 4-1/2", 21" × 21-1/2"The drawer box, Baltic birchSheets A and B
Base toe-kick front rail, back rail, cross rail24" × 4", 18-3/4" × 4" ×2The toe-kick it stands onDesk offcut and Sheet C
Base back30-1/2" × 23-1/4" × 1/4"The backSheet E

After this lesson you can tell Dry Fit which tools you have, repack the sheets, move rips to the track saw, and cut by setup.

My tools

Until you tick any tools, Dry Fit plans for a full shop: every joint, and every machine at its usual size. Once you say what you have, it plans for that.

  1. Open the project menu, click Project library…, and under Cabinets and storage click Base cabinet. Leave it as it opens, a 24" cabinet with a drawer over a door, and click Make it.
  2. Click Settings (the gear at the top right) and scroll to My tools. Tick the tools you have: here Track saw and Kreg pocket-hole jig.
  3. Under Machines, each machine has its size, or I don't have one: the Table saw's Rip capacity from the blade to the fence, the Jointer's and Planer's Width, and the Bandsaw's Resaw height. Type 18 in Rip capacity, for a jobsite saw, and press Return. Below them, Angles says how far your saws tilt and turn.
Settings, My tools: the track saw and the Kreg pocket-hole jig ticked, and under Machines the table saw at 18 inches rip capacity, a 6 inch jointer, a 13 inch planer and a bandsaw that resaws 6 inches
My tools is kept on this device, for every project.
  1. Close Settings and click a side of the cabinet. The Inspector names it Base side. Its Joinery section now shows only the joints your tools cut: dados, rabbets, box joints, pocket screws and shelf pins. A line under them names the rest and what each needs, such as mortise & tenon (a router or hand tools for the mortise). The shop tips follow the tools you ticked too.
A side of the base cabinet selected, and its Joinery section with dado or groove, rabbet, box joint, pocket screws and shelf pins, and a line naming the joints not shown for these tools
Tick a router and mortise and tenon, dovetails and loose joinery come back.

Optimize sheets

  1. In the project menu, click Optimize sheets…. It shows the sheets Now and After, side by side, before anything changes: 5 sheets → 4 sheets. Saves 1 sheet. With Use My shop's stock first ticked, a piece of the desk's offcuts takes two of the parts, so the cabinet's two sheets of 3/4" birch become one. Allow rotating parts lets plywood parts lie across the sheet. If My shop's stock is empty (you skipped Lesson 10), it reads 5 sheets → 5 sheets. Already as few as it can be. and has no button to click: open built-in-desk.dryfit.json, click Keep all under Leftovers you can still use in the lumber rack, and make the base cabinet again.
  2. Click Use 4 sheets. Every part keeps its size, number, place and joinery; only the sheet it comes from and the cut sequence change.
Optimize sheets on the base cabinet: 5 sheets to 4, with Use My shop's stock first ticked, the sheets now on the left and after on the right, one of them a piece from My shop's stock
A piece it uses from My shop's stock comes into the project, reserved for it.

Check my plan's tool findings

  1. Open Check. Each rip wider than your table saw is a finding, such as The 23-1/4" rip for Base side is wider than your table saw: it rips 18" from the blade to the fence. Click Cut it with the track saw on each, and the cut sequence makes that cut with the track saw.
Check my plan with nine findings that a rip is wider than the 18 inch table saw, each with Cut it with the track saw
With a circular saw ticked and no track saw, the fix is Cut it with the circular saw. Solid wood has findings for the jointer, planer and bandsaw too, as in Lesson 15.

Setup sheets

  1. Open Cut list, hide the lumber rack with the button at the top left, and scroll to Cut sequence. Click By setup. The same cuts are grouped by machine setting, so you set the saw once for every cut that needs it: Setup 2, Track saw: rip to 23-1/4" for a side and the back, then the table saw's rip fence and crosscut sled settings. Each setup says how to set the machine, and each row has its part numbers and the steps it covers.
Cut sequence by setup: Setup 2, track saw rip to 23-1/4 inches for a side and the back; Setup 3 and 4, more track saw rips; Setup 5 and 6, table saw rip fence at 4-1/2 and 4 inches; Setup 7, crosscut sled stop at 24-1/4 inches
A tick in one view ticks the same cut in the other. The shop plan PDF prints the setup sheets after the cut sequence.

What you end up with

A base cabinet planned for the tools in your shop, on one sheet fewer, with every cut grouped by how the saw is set.

The finished base cabinet: a drawer over a door, on a toe kick
The base cabinet: 24" × 24" × 34-1/2".