Lesson 15

Solid wood

Make a red oak coffee table from the library, see which way its grain runs and how far it moves, pick a finish and price it. Then plan its top from rough lumber, with every milling step and what to buy at the yard.

You need: Dry Fit open in your browser. A free account only for the PDFs at the end.

What you'll build

The red oak coffee table on square legs, with name tags on Leg, Front apron, Right apron and Top board 1
The coffee table from the library, its grain, movement, finish and cost worked out. The lesson ends with its top planned from rough lumber in a project of its own.

Overall size 48" W × 24" D × 18" H

Parts key

NameSizeWhat it isFrom
Leg17-1/4" × 1-3/4" × 1-3/4" ×4Square red oak legs, 8/4Board A
Front apron, Back apron43-1/4" × 3"The long aprons, grain matchedBoard B
Left apron, Right apron19-1/4" × 3"The short apronsBoard C
Top board 1 to Top board 448" × 6"The top, glued up from four boardsBoards B to E
Strip108" × 6" ×2Rips from the rough board, each crosscut into two top boardsBoard A, rough
Top board48" × 6" ×4The top from rough lumber, in the Coffee table top projectBoard A, rough

After this lesson you can see and match grain, check wood movement, finish and price a project, and plan parts from rough lumber.

The table from the library

  1. Open the project menu, click Project library…, and under Tables click Coffee table. Leave it at 48" × 24" × 18" with Square legs, aprons joined with Mortise and tenon, the top held with Figure-8 fasteners, and Wood on Red Oak. The line under the choices reads 4 legs, 4 aprons and a top of 4 boards. About 34 board feet of Red Oak. Click Make it.
The Coffee table panel of the project library: 48 by 24 by 18 inches, square legs, mortise and tenon aprons, figure-8 fasteners and red oak, with about 34 board feet of red oak
The library plans the table from surfaced boards, planed to thickness at the store. The last part of this lesson plans the top from rough lumber.

Grain

  1. Click Grain on the view toolbar. Every part gets an arrow on its faces, the way its grain runs. Click the apron across the front, between the two front legs. The Inspector names it Front apron. Its Grain section in the Inspector reads Along its length, the way the board runs, with Flat sawn and Quartersawn to pick as your boards are, and how far it moves: about 1/16" across its 3" width between 30% and 60% humidity (flat-sawn red oak).
The coffee table with grain arrows on the top boards and aprons, the front apron selected, and the Inspector's Grain section: along its length, flat sawn, moves about 1/16 inch across its 3 inch width
The cut list has the same in its Grain column, part by part.
  1. From this view the top hides Back apron (a click there picks the whole top), so click Bottom on the view toolbar, then Shift-click Back apron, so both long aprons are selected, and click Continuous grain in their Grain section. Dry Fit says Match A: Front apron, Back apron, cut side by side from one piece in order, and repacks the red oak so both come off one board, with the figure running on from one to the other. Stop matching takes it off.
The front and back aprons selected, and their Grain section with Continuous grain, Book-matched and Stop matching
Book-matched needs a board thick enough to resaw into two leaves; the line under it says how thick.

Wood movement

  1. Click 3D on the view toolbar to turn the view back, then click an empty spot of the floor to clear the selection. In the Project panel, Seasonal humidity has Driest, % at 30 and Most humid, % at 60: The wood goes from about 6.2% to 11.0% moisture. That's a house heated in winter. Every movement figure, and Check my plan's checks for tops and panels that can't move, come from this range. The library held the top with figure-8 fasteners, so it's free to move.
  2. For a table that goes somewhere damp in summer, type 80 in Most humid, % and press Return. The wood now goes to 16.0%. Open Check: each tenon is a finding, such as Back apron and Leg are glued across the grain. Along the 2-1/4" glue line the apron grows and shrinks about 3/32" more than the leg, which doesn't move that way.
  3. To keep the damp-summer range, click Glue the middle only on each finding. The tenon is then glued in the middle 1-5/8" only, the rest stays dry so the apron can move, and the finding goes. For a heated house, type 60 again instead, and the findings go.
Check my plan at 30 to 80 percent humidity: eight findings that an apron and a leg are glued across the grain, each saying the apron moves about 3/32 inch more than the leg along the 2-1/4 inch glue line
Wood movement is checked for solid wood only: plywood and MDF don't move this way.

Finish

  1. In the Project panel, under Finish, set What goes on to Wipe-on poly. Coats starts at 3, and Finish the insides too is ticked. The line under it reads 24.8 sq ft to finish on 12 parts. A part's own Inspector has a Finish choice too, for a part that takes a different one.
The Project panel's Finish section: wipe-on poly, 3 coats, finish the insides too, and 24.8 square feet to finish on 12 parts
Faces against another part, in a joint or on the floor don't count. Faces that look into the piece count when Finish the insides too is ticked.

Cans and cost

  1. Open Cut list. Materials to buy now ends with the finish, in the cans it's sold in: Wipe-on poly: 1 quart (3 coats on 24.8 sq ft: 17 oz with 10% extra, 15 oz left over), after the 10 figure-8 fasteners.
  2. In Cost, set Per on the 4/4 red oak to a board foot and type your yard's price, here 7.25. Do the same for the 8/4 at 9.50. Each line you change gets a Reset, and the prices stay with the project. The total here is $238.33: $209.83 of wood, $4.50 of fasteners and $24.00 of finish.
Materials to buy with the red oak boards, 10 figure-8 fasteners and 1 quart of wipe-on poly, and the Cost table with 7.25 and 9.50 typed per board foot, for a total of 238.33 dollars
The line under the total says how much of it is offcuts, kerf and finish left over.

The top from rough lumber

Rough lumber is cheaper by the board foot, and you mill it flat and square yourself. Plan the top in a project of its own: Dry Fit adds the room each blank needs to mill, and the cut sequence starts with the milling.

  1. Start a new project with New project in the project menu, then click Untitled project at the top and type Coffee table top in the Name box. In the lumber rack, click Hardwood, then Rough under As it comes. Pick Red Oak and a thickness: 4/4 (1"), 5/4 (1-1/4"), 6/4 (1-1/2") or 8/4 (2"). Leave it on 4/4.
  2. Rough boards come in random sizes, so type the board you measured: Width 13 and Length 9'. The rack says About 9.8 board feet. Click Add rough board to shop.
The lumber rack on Hardwood, Rough: red oak, 4/4, 13 inches wide and 9 feet long, about 9.8 board feet, and Add rough board to shop
Type each board as you measured it at the yard, or a typical size to plan with.
  1. Click Rip, type 6, set How many to 2, type Strip in Name the strips and click Rip 2 strips. In the shop lists two Strip, 108" × 6", each to become two top boards, and Offcut A1, 108" × 3/4". Click a Strip, click Crosscut, type 48, set How many to 2, name them Top board, and click Crosscut 2 pieces. Then click the other Strip and do the same. In the shop now lists four Top board, 48" × 6", and the offcuts A1 to A3. A part sawn from 4/4 rough comes off at 3/4", the thickness it mills to.
  2. Lay the four Top board parts flat side by side: click each in In the shop, Lay flat, then Back edge 0, 6, 12 and 18. Click one, Shift-click the other three, and press G to glue them up.
  3. Open Check. Board A's parts sit too close to mill: each blank needs 2" more at each end and 1/4" more in width than its part. Click Lay out Board A with room to mill. The other four say the 6-1/4" blanks are wider than a 6" jointer, so the milling plan flattens them on the planer with a sled. Lesson 16 sets your own jointer's width.
Check my plan on the rough board: Board A's parts sit too close to mill, with the fix Lay out Board A with room to mill, and four findings that a top board's blank is wider than the jointer
Each fix is one step: Undo takes it back.
  1. Open Cut list. Milling lists each blank, here Top board ×4, 4 × 52" × 6-1/4" × 4/4, from the allowances: 2" over at each end for snipe, 1/4" in width and thickness to clean up, and 20% more to buy for defects. Change allowances opens Snipe, extra at each end, Width to clean up, Thickness to clean up, Extra for defects and Shortest blank to plane.
  2. Materials to buy is the yard's list: 4/4 Red Oak, rough, random widths and lengths, 11.0 board feet, with 9.0 bf in the blanks plus 20% for defects. Board A holds 9.8. Cost prices rough lumber at the board feet to buy.
The cut list's Milling section with four 52 by 6-1/4 inch blanks from Board A, Materials to buy with 11 board feet of rough 4/4 red oak, and the Cost table
The milling allowances are kept with the project.
  1. Scroll to Cut sequence. It starts with the milling, one machine at a time: get Board A and mark the blanks, rough cut them, flatten a face, joint an edge, plane to 3/4", rip to 6", square an end and crosscut to 48". Then the glue-up.
The cut sequence for the rough top: get Board A, rough cut 4 blanks 52 by 6-1/4 inches, flatten one face on the planer with a sled, joint an edge, plane to 3/4 inch, rip to 6 inches, square an end and crosscut to 48 inches, then glue up
Each step says why: here the board is wider than the jointer, so it's ripped before a face is jointed.

What you end up with

A red oak coffee table with its grain, movement, finish and cost worked out, and a plan for its top from rough lumber with every milling step.

The finished red oak coffee table: four square legs, four aprons and a top of four boards
The coffee table: 48" × 24" × 18" in red oak, finished with wipe-on poly.