Lesson 17

A built-in from a photo

Tape a printed target to the wall, take a photo, and let Dry Fit read the wall. Check the sizes against your tape, settle the layout of a desk wall with pocket doors, build it, and change it later with Edit built-in.

You need: Dry Fit open in your browser, a printer that prints at 100%, tape, a tape measure and a phone camera. A free account and a photo read for the read itself, and the account for the PDF.

What you'll build

The desk wall built from a photo, with name tags on the Desktop, the Kneehole door, a Monitor bay door and the base and upper doors
The desk wall as Dry Fit builds it from the photo, with pulls: a base cabinet either side of the kneehole, the desktop, and uppers with the monitor bay.

Overall size 64-5/8" W × 24-3/4" D × 84" H

Parts key

NameSizeWhat it isFrom
Desktop64-5/8" × 24"The desk top, across the whole wallSheet A
Left base side, Right base side25-1/4" × 24" ×2 eachSides of the two base cabinetsSheets A, B
Left base door, Right base door25-1/8" × 15"The base cabinets' doorsSheet C
Kneehole door28-5/8" × 16-1/16" ×2The pocket doors that close the kneeholeSheet B
Left upper side, Right upper side36" × 14-1/4" ×2 eachSides of the two upper cabinetsSheets C, D
Left upper door, Right upper door35-7/8" × 13-11/16"The upper cabinets' doorsSheet E
Monitor bay side54" × 14-1/4" ×2Sides of the monitor baySheet C
Monitor bay door53-7/8" × 8-5/8" ×4Bi-fold pocket door leaves, two a doorSheets E, F
Monitor bay back54" × 34-1/4"The bay's 1/4" backSheet G
31 moreEach cabinet's top, bottom, shelves, back, toe-kick rails and fillers, named for the cabinet, such as Left base topSheets A to H

After this lesson you can turn a photo of a wall into a built-in, check its sizes and layout, and change it later with Edit built-in.

The target

The target is a square of known size. In the photo it tells Dry Fit how big the wall is, so the main sizes are measured instead of guessed.

  1. Open the project menu and click Start from a photo. Under Which target is in the photos?, the line No target yet? has the paper one for Letter or A4. Download it and print it at 100% (actual size): turn off Fit to page and Scale to fit.
  2. Check the ruler on the sheet: the bar must measure 100 mm. If it doesn't, the print was scaled; print it again.
  3. Tape the sheet flat to the wall at all four corners, around mid-height and clear of dark things like door trim. Take the photo as straight-on as you can, with the wall's corners at the floor and the ceiling in the frame, all four corners of the target's black frame in it, and your hands off the target. Get the target big in the frame: step closer or zoom in.
The paper target, Letter size: a 180 mm black frame, a 100 mm ruler bar, and the lines print at 100 percent, check the ruler, and tape it flat at all four corners around mid-height
The paper target is 180 mm. A 3D-printed 200 mm one goes flat on the wall too, never standing on the floor.

The read

  1. Back in Start from a photo, click Add photos and pick 1 to 3 photos of the wall. Dry Fit looks for the target in each: Target found on photo 1. Click Paper 180 mm.
  2. In What do you want built here?, say it in your own words: A desk wall: a cabinet either side of a kneehole with pocket doors, and uppers with a monitor bay in the middle.
Start from a photo with one photo of the wall added and the target found on it, Paper 180 mm picked, and the description of a desk wall typed in
With None, every size is an estimate: write one size you know in the description and the rest is scaled from it.
  1. Click Read the wall. The read needs a free account, and each one uses one of your photo reads; the next step says how many you have left.

About these pictures. They were made from a real photo of a wall with the paper target taped flat. Your photo of your wall gives your own sizes and sections.

Check the sizes

  1. Check the sizes shows the photo with the wall's outline and its blue corners, and every size Dry Fit read. Under each is where it came from: measured from the target, estimated, or you. Here the width is 64-5/8", measured from the target. If a corner sits off the wall's corner, drag it on and the sizes measure again.
  2. Check each size against your tape. The ceiling reads 86-3/8", but the photo doesn't show where the ceiling meets the wall on the left, and the tape says 8'. Type 96 in Ceiling height and press Return. The note at the top, Approximate: the target was small in the photo, says the same: step closer next time.
Check the sizes: the photo of the wall with the outline's four blue corners and the target marked, and the sizes: wall 64-5/8 inches wide and 86-3/8 inches high, measured from the target, with the lower and upper runs and their sections estimated
The top of a wall is the hardest part of a photo to read: the dialog says to check the ceiling with your tape.

The layout

  1. Click Next: layout. Check the layout draws what Dry Fit will build, from the front, with every size. Each section has what it is (Cabinet, Open shelves, Kneehole, Monitor bay) and its front. The kneehole here has Pocket doors: With pocket doors, the kneehole is 29-3/8" wide between the pockets.
  2. The monitor bay's pocket doors don't fit: The Monitor bay's pocket doors are 17-3/8" wide and the bay is 14" deep inside. They need their width plus 1" to slide back. Under it are the fixes: Bi-fold pocket doors, Make the uppers 18-5/8" deep and Plain doors. Build stays off until it fits.
Check the layout with the monitor bay's pocket doors too wide for the 14 inch deep uppers, and the fixes Bi-fold pocket doors, Make the uppers 18-5/8 inches deep and Plain doors
Each fix clears the problem without making a new one.
  1. Click Bi-fold pocket doors. Each door is now two leaves that fold before they slide back: With bi-fold pocket doors, the Monitor bay is 29" wide between the pockets. Undo takes back any edit on this step.
The layout after Bi-fold pocket doors: the kneehole 29-3/8 inches and the monitor bay 29 inches wide between the pockets, with Undo and Build
Plain doors would also fit, swinging open instead of sliding back.

Build, then Edit built-in

  1. Click Build. Dry Fit makes every part, 53 here, from the cabinets and the desktop to the doors and shelves, and puts the pocket door sets on the Hardware list. Click Show doors opening: the doors swing, and the pocket doors swing open and slide back.
The built desk wall, 64-5/8 by 24-3/4 by 84 inches, with its doors open: two base cabinets either side of the kneehole, the desktop, and the uppers with the monitor bay
From here it's a project like any other: the cut list, Check my plan and the shop plan all work on it.
  1. To change it later, click Edit built-in in the project menu (or in the Project panel). The layout step opens again with the sizes it was built from, titled Edit built-in. No photo is read, so it doesn't use a photo read. Set Knobs or pulls to Pulls and click Build: the same project is rebuilt.
Edit built-in on the desk wall: the layout step again, with Knobs or pulls set to Pulls
Edit built-in keeps the project's prices and finish.

What you end up with

A desk wall planned from a photo of the wall: base cabinets either side of a kneehole with pocket doors, a desktop, and uppers with a monitor bay behind bi-fold pocket doors.

The finished desk wall with its doors shut and pulls on every door
The desk wall: 64-5/8" W × 24-3/4" D × 84" H.