Lesson 2

Stand up the first cabinet

Stand the sides and shelves of the first base cabinet in the corner by typing where each one goes.

You need: The parts from Lesson 1.

What you'll build

The first base cabinet in 3D: two Side parts standing on end with three Shelf parts between them, each tagged with its name
The first base cabinet: two sides standing in the corner and three shelves between them, not joined yet. The Overall in the status bar is bigger: it also counts the parts still lying out front.

Overall size 18" W × 23-1/4" D × 29-1/4" H

Parts key

NameSizeWhat it isFrom
Side29-1/4" × 23-1/4" ×2The cabinet's sides. You cut four; this lesson uses the first two.Sheet A
Shelf17" × 23" ×3Bottom, middle and top shelf. You cut six; this lesson uses the first three.Sheet B

After this lesson you can stand a part up, type where it goes, set the gap between two parts, and turn a part with the keys.

Back in Shop, click Leftovers in the toolbar to hide the offcuts, then Fit to see every part. They all lie out in front of the build area, where Lesson 1 cut them. Pick parts by their rows in In the shop at the bottom left: it lists four Side rows under Sheet A and six Shelf rows under Sheet B, and this cabinet uses the first two and the first three.

You place each part by typing three numbers under Position in the right panel. Typing lands exactly, so this lesson types every position. The numbers are measured from the corner: the faint lines on the floor marked Left wall and Back wall meet there. Left edge is how far the part's left face is from the Left wall, Back edge how far its back face is out from the Back wall, and Off floor how high its bottom is. Type a number and press Return.

  1. Click the first Side row (29-1/4" × 23-1/4") under Sheet A. Under Position, click On end so it stands 29-1/4" tall. Type 0 in Left edge, 0 in Off floor and 0 in Back edge. It now stands in the corner where the Left wall and Back wall lines meet, 23-1/4" deep from front to back.
The first Side standing on end in the corner where the Left wall and Back wall lines meet, with Position reading 0, 0 and 0
The first Side at 0, 0, 0: in the corner of the two wall lines. If yours runs along the Back wall instead, it's turned: press P, then the left arrow once (or click Turn).
  1. Click the second Side row, click On end, and type 17 1/4 in Left edge, 0 in Off floor and 0 in Back edge. That leaves 16-1/2" between the two Sides.

Set the gap instead. To space a part from another without working out its Left edge: click the part that stays (the first Side), Shift-click the one to move (the second Side), and press M (or click Set the gap (M) under Position). Type 16 1/2 and press Return. Touch closes the gap, and the Flush buttons line faces up. Each is one undo step.

Set the gap open between the two Sides, with 16 1/2 typed, the Touch and Flush buttons, and a dimension line between the Sides
Set the gap, with 16 1/2 typed: Return moves the second Side so the gap is exactly that.
  1. Click the first Shelf row (17" × 23") under Sheet B. It already lies flat, with its 17" running left to right. It's the bottom shelf: type 1/2 in Left edge, 0 in Off floor and 1/4 in Back edge. The shelf is 17" long but there's only 16-1/2" between the Sides, so at Left edge 1/2" it goes 1/4" into each Side; red shows the overlap. In Lesson 3 those overlaps become the dados and rabbets. Back edge 1/4" leaves room behind it for the back panel.
  2. Check the shelf: its ends sit inside the Sides, and its front lines up with theirs, 1/4" in from the back. If it sticks out past the Sides at the front or back, it's turned: press P, then the left arrow once (or click Turn), and type the three numbers again.
  3. Place the second and third Shelf rows the same way: the second is the top shelf, at Off floor 28 1/2; the third is the middle one, at 14 1/4. Both at Left edge 1/2" and Back edge 1/4". Here are all the numbers.
Part (In the shop row)OrientationLeft edgeOff floorBack edge
First SideOn end000
Second SideOn end17-1/4"00
First Shelf (bottom)Lay flat1/2"01/4"
Second Shelf (top)Lay flat1/2"28-1/2"1/4"
Third Shelf (middle)Lay flat1/2"14-1/4"1/4"
The first cabinet with two Sides and three Shelves in place, the middle Shelf selected with Position reading 1/2, 14 1/4 and 1/4, and the Position keys bar along the bottom of the view
All five parts in place, the middle Shelf selected. Its Position reads 1/2", 14-1/4", 1/4". The bar at the bottom is Position keys (P): the arrows turn, tip and roll the part, 1, 2 and 3 lay it flat, on edge or on end, and Esc closes it.

Dragging. You can also drag a part: press on its wood and slide it across the floor, hold Shift to lift it, and Esc puts it back. Blue tags say what it lines up with, and the wall line it snaps to lights up. It's hard to stop on an exact number, so type the numbers after.

You now have two Side parts and three Shelf parts standing as a cabinet in the corner. The other two Sides and three Shelves still lie out front for Lesson 4. Check still counts 16 to fix: nothing is joined yet.