Make a deck with stairs and a railing from the project library, read the lumber to buy, the fasteners and the notes for your building department, then make a shed and read its buy list.
Time20 min
BuildsA 12' × 10' deck and an 8' × 10' shed
You need:Dry Fit open in your browser. A free account only for the PDF at the end.
What you'll build
The 12' × 10' deck, 30" up, with stairs on the left. The lesson then makes an 8' × 10' shed the same way.
Overall size179-5/8" W × 123-1/2" D × 66" H
Parts key
Name
Size
What it is
From
Ledger
144" 2×8
Bolted to the house; the joists hang from it
Board A
Rim joist
144" 2×8
Across the joists' outer ends
Board B
Beam
144" 2×8 ×3
Three plies, on the posts
Boards C to E
Post
14-1/2" 6×6 ×3
Under the beam, each on a footing
Board R
Joist
117" 2×8 ×12
16" on centre, ledger to rim
Boards F to Q
Blocking
2×8 ×9
Between the joists
Boards A to C
Decking
132-3/4" 5/4×6 ×21
The deck boards, one ripped narrow at the edge
Boards T to AN
Border
5/4×6 ×3
The mitered picture-frame border
Boards S, AO, AP
Stringer
46-3/4" 2×12 ×4
Notched stair carriages
Board AQ
Tread
48" 5/4×6 ×6
Two boards a step
Boards T to Y
Rail post
44-1/4" 4×4 ×9
The railing's posts
Boards AR to AT
Top rail, Bottom rail
2×4 ×7 each
The rails between the rail posts
Boards AU to AX
Baluster
25-1/2" 2×2 ×55
Between the rails, at most 4" apart
Boards AY to BF
After this lesson you can make a deck or a shed from the library and read its buy list, hardware and notes for your building department.
The library's Outdoor group has two projects, a deck and a shed. Each is framed in dimensional lumber from a few sizes and choices, with a buy list at the lengths a lumber yard sells.
Dry Fit lays out the framing you pick. It doesn't size it for you. The app says so on the Make it panel, at the top of the cut list and on the shop plan's cover, word for word:
Dry Fit lays out the framing you choose. It doesn't check spans, footings, loads or your local building code. Check the joist, beam and post sizes, the footings and the ledger attachment with your building department before you build. Many places need a permit for a deck or a shed.
A deck
Open the project menu (click the project's name at the top) and click Project library…. Under Outdoor, click Deck.
Type 12' in Width, along the house, 10' in Depth, out from the house and 30 in Height of the decking. Dry Fit shows the sizes in inches: 144", 120" and 30". Leave How it stands on Attached to the house.
Under Joists, click 2×8. Leave Joist spacing at 16" on centre, Beam at 3 plies of the joist size, Posts at 6×6 no more than 96" apart, and the decking in 5/4×6 boards of Pressure-treated pine with a 1/8" gap. Set Stairs to On the left side and keep Picture frame border and Railing, 36" high ticked.
The line adds it up as you change things: 12 joists at 16" on centre, 3 posts, 24 deck boards, stairs of 4 risers and a railing. About 58 boards of PT Pine.
Click Make it. The deck stands against a House wall block, which shows where the house is and isn't cut. It has a Ledger on the wall, Joists, a Beam on three Posts, Decking inside a mitered Border, stairs on the left (Stringers and Treads) and a railing of Rail posts, Top rails, Bottom rails and Balusters. Those are the names the 3D view and the cut list use. If what was on the bench isn't saved, Dry Fit asks first: click OK.
141 parts from 58 boards. With the stairs and the railing it measures 179-5/8" W × 123-1/2" D × 66" H.
Click a stair stringer. Its Angles section lists the cuts that make it: a 35.5° miter at each end and a taper to 2-1/4", and its joinery is a Stringer notch: 3 notches, rise 7-1/2", run 10-1/2". The stairs take the fewest risers that keep each one at 7-3/4" or less, with a run of at least 10".
The same cuts are in the cut list's Angles column, and the notches in its Joinery table.
Open Cut list. The safety sentence is at the top in a block of its own. Under it, the Buy list gives the lumber at the standard lengths that waste least, and what each length is cut into: twelve 2×8s at 10' for the joists, one 6×6 at 8' for the three posts, seven 2×2s at 16' and one at 14' for the 55 balusters. Short parts such as blocking come out of the long boards' offcuts first.
The Buy list comes before the parts table, and gets a page of its own in the shop plan PDF.
Under the Buy list, Notes say what the plan leaves to you:
Footings: 3 posts, each on its own concrete footing, and a pad at the foot of the stairs. The concrete isn't sized: ask your building department.
Ledger: the lag screws or through-bolts every 16" are a count for the Hardware list, not a rating. Flash the ledger and check how it fastens to the house.
Stairs: 4 risers of 7-1/2" and 3 treads with a 10-1/2" run, and how to lay out the stringers with a framing square.
Railing: posts at most 6' apart, balusters at most 4" apart, 36" high. Check what your building department wants.
The parts table follows, with every post, joist, board and baluster.
Scroll to Hardware. The fasteners and connectors are counted from the framing, and screws and nails come by the box: 716 deck screws (3 boxes of 350), 18 ledger lag screws, 16 joist hangers and 4 doubles, 12 hurricane ties, post bases and beam brackets for the 6×6 posts, carriage bolts for the rail posts, 4 stair stringer brackets, and structural screws for the beam, rim joist and joists. On parts gives the cut list numbers each goes on.
Materials to buy repeats the boxes with the lumber, and Cost prices them all at rough starting prices you can change.
A shed
Open Project library… again and click Shed. Leave it 96" wide across the gable ends and 120" deep, with 84" walls. Click + by Roof pitch, in 12 until it says 8.
Type 60 in Door opening width and click Double; the door stays in The front gable. Click + by Windows to make it 2, and set Windows in to Both sides. Keep Siding on T1-11 panels.
20 studs, 18 rafters at 8 in 12 and 3 sheets of CDX, 14 sheets of T1-11 and 4 sheets of OSB. About 40 boards of SPF, 9 of PT Pine and 3 of Pine. The same safety sentence sits under it.
Click Make it. If the deck isn't saved to your account, Dry Fit asks before the shed takes its place: click OK, or Cancel and export the deck's plan first. The shed sits on skids under a floor, with stud walls framed round the door and the windows, rafters cut with plumb cuts and birdsmouths, a ridge board, collar ties, fascia, roof sheathing, T1-11 with the openings cut out (Siding and Gable siding in the cut list), and a battened double door (Door and Door batten).
113-1/2" W × 121-7/8" D × 130-3/8" H with the overhangs.
Open Cut list. The Buy list has the framing: 4×6 skids, PT 2×6 floor joists, SPF 2×6 rafters, 2×4s for the plates, studs, corner posts, king and jack studs, 1×6 fascia and 1×4 door battens. The sheets (3 of 3/4" CDX for the floor, 14 of T1-11, 4 of 7/16" OSB for the roof) are under Materials to buy with the hardware: T-hinges and a latch for the door, hurricane ties, and framing and sheathing nails by the box.
Read the shed's Notes before you cut a rafter. They give the rafter layout (56-13/16" along the rafter from the ridge face to the wall's outside corner, then 9-5/8" of overhang), the plumb cut and the birdsmouth, and what isn't planned: shingles, felt and drip edge (about 1.1 squares of roof), the windows themselves (2 rough openings of 24" × 24") and the ground work under the skids.
Change a size in the library and make it again for a new plan: the framing, the buy list and the notes all follow.
What you end up with
A 12' × 10' deck on three posts with stairs, a railing and a picture-frame border, with the lumber to buy at yard lengths, its fasteners by the box and the notes to take to your building department. And an 8' × 10' shed with its framing, sheets and hardware listed the same way.
The deck, 12' along the house and 10' out, 30" up.
The cover carries the safety sentence, and the Buy list has a page of its own after Materials to buy and Cost. Exporting your own needs a free account: click Export plan, pick the paper and the sections, and click Download PDF.