Lesson 14

Angled work

Angled work is any cut that isn't square: miters, bevels, splayed legs and tapers. Miter a picture frame and hold its corners with splines, then make a coffee table on splayed legs and taper them, with every angle and saw setup in the cut list.

You need: Dry Fit open in your browser. A free account only for the PDF at the end.

What you'll build

The red oak coffee table on four splayed, tapered legs, with name tags on Leg, Front apron, Right apron and Top board 1
The coffee table on splayed, tapered legs. The lesson starts with a walnut picture frame in a project of its own.

Overall size 51-3/16" W × 24" D × 18" H

Parts key

NameSizeWhat it isFrom
Long side14" × 2-1/2" ×2The picture frame's top and bottom, walnut, miteredBoard A
Short side12" × 2-1/2" ×2The picture frame's ends, walnut, miteredBoard A
Leg17-13/16" × 1-3/4" × 1-3/4" ×4The coffee table's legs, splayed 10° and tapered on two facesBoard A
Front apron, Back apron42-9/16" × 3"The long aprons, mitered 10° at each endBoards B and C
Left apron, Right apron17-1/2" × 3"The short apronsBoard B
Top board 1 to Top board 448" × 6"The top, glued up from four boardsBoards D to G

After this lesson you can miter a corner and pick what holds it, splay and taper legs, and cut every angle from the setups the cut list gives.

A mitered picture frame

Four walnut sides, each cut to the frame's outside length, laid in a rectangle with their ends overlapping at the corners. Dry Fit then cuts each corner's miter for you.

  1. Start a new project with New project in the project menu, then click Untitled project at the top and type Picture frame in the Name box. In the lumber rack, click Hardwood, pick Black Walnut, 3/4" (4/4), 2-1/2" wide and 6' long, and click Add board to shop.
  2. Click Crosscut, type 14, set How many to 2, type Long side in Name the pieces, and click Crosscut 2 pieces. The two Long side parts, 14" × 2-1/2", are the frame's top and bottom. In the shop, click Offcut A1, 43-3/4" × 2-1/2", the rest of the board, and crosscut two more at 12, named Short side: the frame's ends. In the shop now lists 4 parts and Offcut A1 at 19-1/2" × 2-1/2".
The Crosscut form on a 2-1/2 inch walnut board: 14 inches, 2 pieces, named Long side, with the two pieces marked on the board
The form for the long sides, before you click Crosscut 2 pieces. Cut each side to the frame's full outside length; the miters come off the ends later.
  1. Lay the four sides flat in a 14" × 12" rectangle. Click each part in In the shop, then Lay flat; for each Short side press R as well to turn them 90° so they run front to back. Then drag them into place, or type these numbers. Each corner has two ends lying over each other.
PartOrientationLeft edgeOff floorBack edge
Long sideLay flat000
Long sideLay flat009-1/2"
Short sideLay flat, turned 90°000
Short sideLay flat, turned 90°11-1/2"00
  1. Click a Long side, then Shift-click a Short side that meets it. The Inspector shows Miter: Cuts both ends at 45° so the long points meet at the outside corner, in the face, as a frame.
The four walnut sides laid flat in a rectangle with their ends overlapping, a long side and a short side selected, and the Inspector's Miter section with the Miter the corner button
If the ends don't overlap at the corner, the section doesn't show. Slide each part out to the outside corner.
  1. Click Miter the corner. Both ends are cut at 45°, and the section becomes Mitered corner, with Join: what holds it.
  2. Pick what holds the miter: Glue only, Spline, Biscuits, Dominos, Keys or Pocket screws. Each says what it takes. Click Spline: A 1/4" slot along the miter, 3/8" deep into each part, and a spline 3-1/16" long.
  3. Do the same at the other three corners: select the two sides that meet, Miter the corner, then Spline.
The walnut frame with all four corners mitered, two sides selected, and the Mitered corner section with Spline picked and the slot and spline sizes
Glue only is fine for a small frame; the line under it says end grain to end grain is weak for anything that takes a load.
  1. Open Cut list. The Angles column says what to cut after the blank: Miter both ends 45°, joined with a spline. Cut each side to the length listed, then miter the ends.
The picture frame's cut list: 2 long sides 14 inches and 2 short sides 12 inches, 2-1/2 inches wide in black walnut, with the Angles column reading Miter both ends 45 degrees, joined with a spline
The note under the table: cut the blank to the size listed first, then make the cuts in the Angles column.

Other angles. Any part's Angles section in the Inspector adds a cut by hand: Miter an end, Bevel an end, Bevel an edge or Taper. Each shows in 3D, see-through, until you click Add. Two parts meeting through their thickness, as at a box corner, miter the same way with Miter the corner.

A coffee table on splayed, tapered legs

  1. Open Project library… and under Tables click Coffee table. Under Legs, click Splayed. Splay, degrees appears, at 10. Leave Aprons joined with on Dominos: on splayed legs the long aprons meet the legs at an angle, so they take Dominos or pocket screws. Click Make it.
The Coffee table panel from the project library with Splayed picked under Legs, Splay 10 degrees, aprons joined with Dominos, figure-8 fasteners and red oak
Splayed legs lean out 8 to 15°.
  1. Click a leg low down, near its foot (higher up, the click can land on the top and pick all four top boards). The Inspector names it Leg. Its Tilt section reads Leans 10°: the library leaned it with Tilt, and its Angles section lists the two cuts that set it flat on the floor and flat under the apron, Bevel, bottom end 10° and Bevel, top end 10°.
A splayed leg of the coffee table selected, with the Angles section listing a 10 degree bevel on each end and the Tilt section reading Leans 10 degrees
To splay legs you placed yourself, select them all and use Tilt: Outward leans each one away from the middle, and Cut the ends level adds the end cuts.
  1. With the leg selected, click Taper under Angles. Dry Fit picks an inside face and drafts the taper: Taper, right face to 1-1/16", starting 4" down. Face, Narrow end, Starts from the wide end and Size at the narrow end change it. Click Add.
  2. Click Taper again for the leg's other inside face, and Add. Do the same on the other three legs: Dry Fit picks each leg's own inside faces.
The taper drafted on a splayed leg, drawn see-through in 3D, with the fields Face, Narrow end, Starts from the wide end and Size at the narrow end, and Add
The draft shows see-through in 3D until you click Add or Cancel.
  1. Open Cut list and hide the lumber rack with the button at the top left. Each leg's Angles reads Bevel both ends 10°; taper 2 inside faces from 1-3/4" to 1-1/16", starting 4" down, and the long aprons Miter both ends 10°, joined with Dominos.
The coffee table's cut list with the Angles column: legs beveled both ends 10 degrees and tapered on 2 inside faces, and the front and back aprons mitered both ends 10 degrees
The four legs are listed in two rows of 2.
  1. Scroll to Cut sequence and click By setup. The cuts are grouped by machine setting, and the angles have setups of their own: the miter saw swung to 10° for the long aprons' ends, the blade tilted to 10° for the legs' ends, and the table saw's taper jig, 11/16" over 13-13/16", with where to mark each leg.
Cut sequence by setup on the coffee table: Setup 14, miter saw miter at 10 degrees for the back and front aprons; Setup 15, miter saw bevel at 10 degrees for the four legs; Setup 16, table saw taper jig 11/16 inch over 13-13/16 inches, then the Domino setups
Each setup says how to set the saw and to make a test cut on scrap first. Setup sheets print in the shop plan PDF too.

What you end up with

A walnut picture frame with splined miters, and a red oak coffee table on splayed, tapered legs, with every angle in the cut list and the saw setups to cut them.

The finished red oak coffee table with four splayed, tapered legs and a top of four boards
The coffee table: a 48" × 24" top at 18" high. The splayed feet stand out past the top, 51-3/16" overall.