Lesson 13

Shaped parts and full-size templates

Arch the aprons of a side table, shape a set of bracket feet, and print every curve at full size to trace onto the wood.

You need: Dry Fit open in your browser. A free account for the templates and the PDF, and a printer that prints at 100%.

What you'll build

The red oak side table with an arch cut into each apron, with name tags on Front apron, Right apron, Leg and Top board 1
The side table, its four aprons arched. The lesson ends with four cherry bracket feet in a project of their own.

Overall size 20" W × 20" D × 24" H

Parts key

NameSizeWhat it isFrom
Leg23-1/4" × 1-3/4" × 1-3/4" ×4Square red oak legsBoard A
Front apron, Back apron, Left apron, Right apron16-1/4" × 3"The aprons, each with a 1" arch on its bottom edgeBoard B
Top board 1 to Top board 420" × 5"The top, glued up from four boardsBoard C
Bracket foot10" × 5-1/2" ×4Cherry feet for a small chest, in the Bracket feet projectBoard A

After this lesson you can shape a part's edge or end, and print a shaped part full size to trace from.

Arched aprons

Any part can take an arc on an edge or an end, cut in as an arch or curving out, and rounded corners. The rectangle is still what you cut from the board first; the shape is cut inside it.

  1. Open the project menu, click Project library…, and under Tables click Side table. Leave it at 20" × 20" × 24" with square legs in red oak, and click Make it.
  2. Click the apron across the front, between the two front legs. The Inspector names it Front apron. In the Inspector, below Size, is Shape, with four starts: Arched apron, Bracket foot, Curved front and Round corners. Click Arched apron.
  3. The arch is sized from the apron: Edge Bottom edge, Curve Cut in, Starts 1-5/8", Ends 14-5/8" and Rise 1-1/16". Type 1 in Rise and press Return. Starts and Ends are measured from the apron's left end.
The side table's front apron selected, with an arch cut into its bottom edge, and the Inspector's Shape section: bottom edge, cut in, starts 1-5/8 inches, ends 14-5/8 inches, rise 1 inch
A change that breaks a rule, such as a rise that leaves too little wood, is refused with the reason.
  1. Do the same for the other three aprons. From this view the top hides Back apron and Left apron (a click there picks the whole top), so click Bottom on the view toolbar first: from underneath, all four aprons show. Click Back apron, Left apron and Right apron in turn, and on each click Arched apron and type 1 in Rise. Then click Front on the view toolbar to see the arches straight on.
Front view of the side table with the arched front apron between the legs
Remove under a shape takes it off. Each change is one undo step.
  1. Open Diagrams. Each apron's rectangle is drawn dashed and pale on its board, with the arch filled inside it, so you can see the wood that comes off after the saw.
Cutting diagrams for the side table: the legs on an 8/4 red oak board, the four arched aprons on a 4/4 board with their arches drawn inside the cut rectangles, and the top boards
The red marks at the ends of the aprons are the tenons' joinery.
  1. Open Cut list. A Shape column appears once a part is shaped: Arch on the bottom edge, 1" rise.
The side table's cut list with the Shape column reading Arch on the bottom edge, 1 inch rise, for the four aprons
The size columns are still the rectangle to cut first.

Full-size templates

  1. Click Export plan (this needs a free account). With a shaped part in the project, the dialog has a Full-size templates block: here 4 shaped parts on one template at actual size, on 3 pages of US Letter with overlap, marks to line them up and scale bars to check the print. The four aprons are the same shape, so they share one template. The paper picked above it sets the page count. Click Download templates.
The Export shop plan dialog with the Full-size templates block: 4 shaped parts on one template at actual size, on 3 pages of US Letter, and the Download templates button
The templates are their own PDF, beside the shop plan.
  1. The first page is notes: how to print, check, trim and tape the pages, and a table of the templates and their pages. Then each distinct shape is drawn once at 1:1, with how many to make (the aprons are one template, ×4), its cut size dashed and its outline solid, with a grain arrow. The header says which face is up, which edge goes at the top of the page, and the page's place: A1 is the top left, A2 to its right.
  2. Print at 100% (Actual size), not Fit to page. Before you cut, measure the two scale bars at the foot of each page: the 100 mm bar and the 4" bar. If either is off, the printer scaled the page.
  3. Trim each page on its dashed left and top edges, lay it over the page to its left so the circles line up, and tape them. Cut the apron to its size first, lay the template on the face it names with the named edge at the top, then trace the line and cut to it.
A template page for the four aprons at full size, marked ×4: the cut size dashed, the arch's outline, a grain arrow, registration marks at the right edge where the next page overlaps, and a 100 mm and a 4 inch scale bar at the foot
Page A1 of the apron template. The marks on the right edge meet the same marks on page A2.

Bracket feet

Shapes work on parts you cut yourself, too. These four feet are for a small chest.

  1. Start a new project with New project in the project menu (Dry Fit asks first, as the side table isn't saved). Click Untitled project at the top and type Bracket feet in the Name box. In the lumber rack, click Hardwood, pick Cherry, 3/4" (4/4), 5-1/2" wide and 4' long, and click Add board to shop.
  2. Click Crosscut, type 10, set How many to 4, type Bracket foot in Name the pieces, and click Crosscut 4 pieces. In the shop now lists four parts called Bracket foot, 10" × 5-1/2", the feet for a small chest, and Offcut A1, 7-1/2" × 5-1/2", what's left of the board. Click each Bracket foot in turn and click On edge to stand it up.
  3. Click a Bracket foot, then Bracket foot under Shape: a curve cut into the bottom edge from 4" to the end at 10", 2-3/4" deep. Do the same on the other three. The square end goes at the chest's corner.
Four cherry bracket feet standing on edge, the first with a curve cut up to its right end, and the Inspector's Shape section: bottom edge, cut in, starts 4 inches, ends 10 inches, rise 2-3/4 inches
Round corners puts a radius on the corners instead; tick Different each way (an ellipse quarter) for an oval corner. Curved front bows a front edge out.

What shapes can be. One arc to a side, between two points, cut in or curving out, and rounded corners. No coves, ogees, holes or free curves, and nothing through the thickness, such as a roundover.

What you end up with

A red oak side table with four arched aprons, a cut list that gives the blank and the shape for each, and full-size templates for the arches.

The finished side table in red oak with arched aprons on all four sides
20" W × 20" D × 24" H, in 12 parts.