Lesson 12

A base cabinet with doors and drawers

Make a base cabinet with a drawer over a door from the project library, then hang an inset frame-and-panel door on a face frame yourself, and see the hinges, pulls and slides it takes.

You need: Dry Fit open in your browser. A free account only for the PDF at the end.

What you'll build

The second base cabinet with its hard maple face frame and inset frame-and-panel door, with name tags on Base side, Face frame stile, Face frame top rail and Door 1 panel
The cabinet you hang the door on yourself. The first one, straight from the library, has a drawer over a full-overlay door.

Overall size 24-1/2" W × 24" D × 34-1/2" H

Parts key

NameSizeWhat it isFrom
Base side30-1/2" × 23-1/4" ×2The cabinet sidesSheet A
Base bottom, Base top23" × 23"The box's bottom and topSheet B
Base toe-kick front rail, back rail, cross rail24" × 4", 18-3/4" × 4" ×2The toe-kick it stands onSheet B
Base back30-1/2" × 23-1/4" × 1/4"The backSheet C
Face frame stile30-1/2" × 1-1/2" ×2The face frame's uprights, hard mapleBoard D
Face frame top rail, bottom rail21-1/2" × 1-1/2"The face frame's crosspiecesBoard D
Door 1 stile27-3/8" × 2-1/4" ×2The door's uprightsBoard D
Door 1 rail17-5/8" × 2-1/4" ×2The door's crosspiecesBoards D and E
Door 1 panel23-9/16" × 17-9/16" × 1/4"The door's flat maple plywood panelSheet F

After this lesson you can make a cabinet from the library, open its doors and drawers, and hang a door of your own on any opening.

From the library

The library's base cabinet is a frameless plywood box on a toe-kick, with its doors, drawer, hinges and slides already fitted. Start there to see what a finished cabinet carries.

  1. Open the project menu (click the project's name at the top) and click Project library…. Under Cabinets and storage, click Base cabinet.
  2. Leave Width 24", Depth 24" and Height 34-1/2". Keep Fronts on A drawer over doors and Shelves at 1. Under Knobs or pulls, click Pulls. The line at the bottom adds it up: a cabinet, 1 drawer, 1 door and 1 shelf, and the sheets it takes.
The Base cabinet panel from the project library: width 24, depth 24 and height 34-1/2 inches, Fronts set to A drawer over doors, 1 shelf, birch plywood and Pulls picked, with a summary of the sheets it takes
Fronts also offers Doors or Drawers. Drawers need a cabinet at least 14" deep for their slides.
  1. Click Make it. Then click Show doors and drawers opening on the view toolbar. The door swings open on its hinges and the drawer slides out, so you can check they clear each other and the room. Click the same button again to close them before the next step: while the door is open, clicking where it hangs picks the opening behind it instead.
The base cabinet with its drawer pulled out and its door swung open, showing the drawer box, the shelf on its pins and the toe-kick
A single door or drawer opens on its own from the Inspector.
  1. With the door closed, click it. The Inspector names it Base door, and its Door section says how it hangs (Full overlay, opens 110°), opens or closes it with Open it, and moves the hinges with Hinge on the left or Hinge on the right. The line under it gives the cup boring for the hinge: 2 cups 35 mm across, 1/2" deep, centred 7/8" in from the edge, at 3" and 21-1/4" down from the top.
The cabinet's door selected, with the Inspector's Door section: full overlay, opens 110 degrees, Open it, Hinge on the right, and the cup boring for two 35 mm hinge cups
Mark the cups from this line, or from the joinery table in the cut list.
  1. Open Cut list and scroll to Hardware. It lists the drawer slides (a 22" full-extension, side-mount pair), two full-overlay hinges, the pulls for the door and the drawer, four shelf pins and the pocket screws for the toe-kick, each with the parts it goes on. Materials to buy repeats them under the sheets.
The cut list's Hardware table: 1 pair of 22 inch full-extension side-mount drawer slides, 2 hinges with 35 mm cups, 18 pocket screws, 2 pulls on 3-3/4 inch centers and 4 shelf pins, then Materials to buy
The On parts column gives the cut list number each piece of hardware goes on.

By hand: a face frame and an inset door

Now hang a door yourself. A door goes on an opening: the clear rectangle a cabinet leaves at its front, between its sides, bottom, top and any dividers. Dry Fit finds the openings in whatever you build, from the library or by hand.

  1. Open Project library… again and click Base cabinet. Set Fronts to Doors, click − to make Shelves 0, and click Make it. If the first cabinet isn't saved, Dry Fit asks first.
  2. Click the door. The Inspector names it Base door. Click Throw away at the foot of the Inspector. The front of the cabinet is open, and the cabinet has 9 parts.
  3. Move the pointer over the front of the cabinet: the opening lights up in blue. Click it. The Inspector shows Bay 1 and its Clear opening, 22-1/2" × 29", then Face frame and Add doors. Shift-click more openings to put doors on them all at once.
The open base cabinet with its front opening outlined in blue, and the Inspector's Face frame section: hard maple, 3/4 inch thick, 1-1/2 inch stiles, rails and mullions, stiles 1/4 inch proud of the sides, pocket screws, and Add face frame
The face frame line says what it will make: 2 stiles, a top rail and a bottom rail, the stiles 30-1/2" long.
  1. Under Face frame, leave Wood on Hard Maple, Stiles sit on 1/4" proud of the sides and Joint on Pocket screws. Click Add face frame. Dry Fit cuts four parts, Face frame stile (two of them), Face frame top rail and Face frame bottom rail, joins them, and fastens the frame to the cabinet's front edges with Dominos. Take the face frame off in its panel takes it back off.
  2. Dry Fit leaves the 4 face frame parts selected. Click the opening again: it's now the opening inside the face frame, and Clear opening reads 21-1/2" × 27-1/2". Under Add doors, pick how the door sits:
    • Full overlay covers the cabinet's front edges, with a small gap at each edge.
    • Half overlay covers half of each edge.
    • Inset sits inside the opening, flush with the front.
    Click Inset. The hinge list dims the hinges that aren't made for the way you picked, so click the Everbilt Frameless soft-close inset hinge.
  3. Under Door style, click Frame and panel. Keep Frame wood Hard Maple, Stiles and Rails 2-1/4", Joint Cope and stick (or Stub tenon and groove), and Panel Flat plywood in maple plywood. Raised solid wood makes a solid panel sized to move with the seasons.
  4. Under Knob or pull, click the Amerock Everett 3-3/4" (96 mm) bar pull. The line above Add door now reads: One door: 21-3/8" × 27-3/8", 2 hinges each; a 1/4" × 3/8" groove; flat panel 17-9/16" × 23-9/16", 1/16" at each edge, from leftovers first.
Add doors on the face frame's opening: Inset picked under How they sit, the gaps, Frame and panel picked under Door style, hard maple stiles and rails 2-1/4 inches wide, Cope and stick, and a flat maple plywood panel
Each store link in the hinge and pull lists opens the product's page, so you can check the price.
  1. Click Add door, then Show doors opening. The door is a glue-up of five new parts: two Door 1 stile, two Door 1 rail and Door 1 panel, hung on two inset hinges with the pull on the stile away from them.
The base cabinet with its maple face frame and the inset frame-and-panel door swung open, showing the door's stiles, rails and panel
One undo step takes the whole door off again.
  1. Open Cut list. Every stile, rail and panel is a part in the parts table. Doors and face frames says how each is made, and Hardware now lists the pull, the inset hinges, 22 Domino tenons for the frame and the pocket screws. Hardware to buy gives the packs to buy and where.
The cut list's Doors and face frames table for the cabinet, describing the face frame and the frame-and-panel door, above the hardware
The Assembly table lists the cope and stick joints and the stick and groove that holds the panel.

What you end up with

A 24" base cabinet with a hard maple face frame and an inset frame-and-panel door, its hinges and pull, and a cut list for the case, the frame and the door. The first cabinet, from the library, has the drawer, its slides and the full-overlay door.

The finished base cabinet with a maple face frame and an inset frame-and-panel door with a black bar pull
The finished cabinet, 24-1/2" W × 24" D × 34-1/2" H with the face frame on.

Exporting your own needs a free account: click Export plan, pick the paper and the sections, and click Download PDF.